Alerts
Look up operating alerts and errors for your machine. Search by code, name or description.
Alerts
| Alert or error | Type | Short description |
|---|---|---|
| AA-1 · Wrong voltage | Alert | |
| AA-2 · Absence of auxiliary voltage | Alert | |
| AA-3 · DHW without consumption | Alert | |
| AA-4 · High Temperature ST1 | Alert | |
| AA-5 · High Pressure SP1 | Alert | |
| AA-6 · High Pressure SP2 | Alert | |
| AA-7 · Low oil level SN1 | Alert | |
| AA-8 · Clogged Filter 1 | Alert |
Errors
| Alert or error | Type | Short description |
|---|---|---|
| ER-1 · CAN communication error with Joystick. | Error | If the ecu does not receive addresses 1696 and 1697, the joystick dog error is triggered. |
| ER-2 · CAN communication error with ECU. | Error | If the joystick does not receive the 1695 address, the ecu canine error is activated. This error is already programmed into the joystick microphone |
| ER-3 · ACS error. | Error | The ACS error is triggered if two simultaneous conditions are met. If the ACS should be active and the sense does not exceed a certain voltage value (1.6-2V), the ACS error is triggered |
| ER-4 · Error in temperature sensor. | Error | If the temperature sensor fails, we will obtain a value of 0 V (-25ºC), so if we measure a temperature lower than 20ºC, the error of the temperature sensor failure is activated |
| ER-5 · Error in right interstrain sensor. | Error | If we do not detect the inductive sensor of the right intervine for X amount of time, the error of the right AI is activated. The sensor always detects less when the intervine is retracted |
| ER-6 · Error in left interstrain sensor. | Error | If we do not detect the left interstrain inductive sensor for X amount of time, the left AI error is triggered. The sensor always detects less when the interstrain is retracted |
| ER-7 · CAN communication error with CR9996-1. | Error | If the ecu does not receive addresses 385 or 641, the CR9996 module can error is triggered (Configuration 1) |
| ER-8 · CAN communication error with CR9996-2. | Error | If the ecu does not receive addresses 386 or 642, the CR9996 module can error is triggered (Configuration 2) |
| ER-9 · Error in angle flip sensor. | Error | If the sensor does not read between the values set by it (0.5 - 4.5 V). |
| ER-10 · Error in RPM sensor of roller. | Error | If we have the engine activated and the sensor does not read revolutions on the rollers |
| ER-11 · Error in the angular sensor of the probe. | Error | If we have the automatic mode activated and the sensor does not read between the values established by it (0.5 - 4.5 V) |
| ER-12 · Error in the angular sensor of the head. | Error | If the sensor does not read between the values set by the sensor (0.5 - 4.5 V). Not currently integrated |
| ER-13 · Error in turbine RPM sensor. | Error | If we have the engine activated and the sensor does not read revolutions in the turbine |
| ER-14 · Error in pressure sensor. | Error | If we have the engines active and the pressure sensor does not read, the error is activated |
| ER-15 · CAN communication error with ECU 1. | Error | CAN communication failure between ECU 1 and the rest of the system. This may be due to a disconnection of ECU 1. |
| ER-16 · Pressure switch sensor error. | Error | Rotary trimmers have a pressure switch to avoid damaging the motors. It is a digital signal, if the pressure switch is activated the motors are deactivated |
| ER-17 · Error in right RPM sensor. | Error | If we start the engine and we do not detect revolutions. The error will remain stuck until the joystick is restarted |
| ER-18 · Error in left RPM sensor. | Error | If we start the engine and we do not detect revolutions. The error will remain stuck until the joystick is restarted |
No alerts or errors match your search.
Available in a future release